| Author |
 Topic  |
|
JPSH120
United Kingdom
1180 Posts |
 Posted - 06 Feb 2013 : 20:09:49
|
Heater & wiper motor back in, slowly starting to take shape!
___________________________________________________________________________
 |
 |
|
|
JPSH120
United Kingdom
1180 Posts |
Posted - 07 Feb 2013 : 20:13:48
|
Was late back from work tonight so didn't get much done other than making the last brake pipe to go to the rear of the car. Did put the rocker cover on to see it in all of it's polished glory.......
___________________________________________________________________________
|
|
|
|
JPSH120
United Kingdom
1180 Posts |
Posted - 26 Feb 2013 : 09:52:45
|
A little more progress to report. All the rear suspension is new (shocks & springs) so a dirty old axle was not going to look right! It has taken some cleaning but well worth it!
I have some satin black to finish it off to match the other components.
I am having my first go at mig welding, there are a couple of small patches required on the underside, not visible so it doesn�t have to be pretty!!
-------------------------------------------
Axle is now finished, so onto the next job!
___________________________________________________________________________
|
Edited by - JPSH120 on 12 Mar 2014 13:18:31 |
|
|
|
HunterGLS
Ireland
95 Posts |
Posted - 04 Mar 2013 : 16:36:39
|
Nice job.
Are you keeping the standard shocks or using the Spax ones? |
|
|
|
JPSH120
United Kingdom
1180 Posts |
Posted - 04 Mar 2013 : 18:32:44
|
quote:
Originally posted by HunterGLS
Nice job.
Are you keeping the standard shocks or using the Spax ones?
Sticking with standard for now, I've got a new pair of boge shocks to go on.
___________________________________________________________________________
|
|
|
|
HunterGLS
Ireland
95 Posts |
Posted - 04 Mar 2013 : 22:04:13
|
I think I will be doing the same.
I didn't know you could get Boge shocks, I've only seen Spax and Armstrong. |
|
|
|
JPSH120
United Kingdom
1180 Posts |
Posted - 04 Mar 2013 : 22:32:29
|
quote:
Originally posted by HunterGLS
I think I will be doing the same.
I didn't know you could get Boge shocks, I've only seen Spax and Armstrong.
I bought them a while ago but presumably they are still available. They must still make some shocks with the correct dimensions etc.
___________________________________________________________________________
|
|
|
|
JPSH120
United Kingdom
1180 Posts |
Posted - 01 May 2013 : 09:05:26
|
I've made a start on what I hope will be the last bit of bodywork repairs needed. This is the junction of N/S/F footwell/sill and it has evidently been repaired previously but over 20 years ago;
___________________________________________________________________________
|
|
|
|
Fastback Thomas
Belgium
423 Posts |
Posted - 02 May 2013 : 19:33:45
|
How a rusty hole always turns out to become a massive gap...
Sadly I know all about it..
Keep up the good work! 
'68 sunbeam rapier fastback {B341006846 OD/LHO}
I like a car that looks normal but really knocks your socks off!!
|
|
|
|
JPSH120
United Kingdom
1180 Posts |
Posted - 03 May 2013 : 19:57:01
|
Good session on the car this afternoon fabricating some repair pieces and also got most of them clipped in place. A bit more fiddling required before the welding can begin;
Weather permitting I will be back on it again on Monday.
___________________________________________________________________________
|
|
|
|
Jon
United Kingdom
221 Posts |
Posted - 03 May 2013 : 23:03:43
|
Looking good but I would have used a bigger piece for the floor section as there doesnt look much over hang for you to weld the section in. If you want to get really tech you could joggle the edge to so it fits really nice Nice clamps by the way
Hillman Avenger MK1 GT,
Commer PB Pick-Up,
Commer PB Panel Van,
Commer Auto sleeper,
Triumph Stag MK1,
Chevette HS x2,
Lancia Delta Integrale,
Fiat Mk1 Uno Turbo,
Rapier Fastback,
MGZS 180kit TD MK2,
MK5 Transit Hallmark 1965-95 celebration,
MK5 Transit 2.5td 150,
|
|
|
|
JPSH120
United Kingdom
1180 Posts |
Posted - 04 May 2013 : 09:14:12
|
Cheers Jon, it's been quite tricky trying to work out how the bottom of the door post is meant to look as it was non existent! And I think you are probably right about the floor piece, I wasn't overly confident about butt welding it in to be honest, if I add some extra it will give some margin for error!
___________________________________________________________________________
|
|
|
|
Jon
United Kingdom
221 Posts |
Posted - 04 May 2013 : 09:49:40
|
Your not far away with the original shape but to add some strength it could do with a flange on the floor pan part facing down and running along the sill section. You could then plug weld it to the inner sill to make it look more oe. Then just run some seam sealer along the joins.If you jogle the edge seam weld and linish it back will almost be invisible repair
Hillman Avenger MK1 GT,
Commer PB Pick-Up,
Commer PB Panel Van,
Commer Auto sleeper,
Triumph Stag MK1,
Chevette HS x2,
Lancia Delta Integrale,
Fiat Mk1 Uno Turbo,
Rapier Fastback,
MGZS 180kit TD MK2,
MK5 Transit Hallmark 1965-95 celebration,
MK5 Transit 2.5td 150,
|
|
|
|
bigt80
United Kingdom
1052 Posts |
Posted - 04 May 2013 : 19:48:00
|
quote:
Originally posted by HunterGLS
I think I will be doing the same.
I didn't know you could get Boge shocks, I've only seen Spax and Armstrong.
Yes, I have to say that in my heyday it was only Spax available as uprated for the rear & Koni's for the front. Mine have now been sitting for 13years, but hope all will be well when it finally gets on the road: still kack-hander to go first. Small update on that on the thread! |
|
|
|
bigt80
United Kingdom
1052 Posts |
Posted - 04 May 2013 : 19:49:05
|
quote:
Originally posted by HunterGLS
I think I will be doing the same.
I didn't know you could get Boge shocks, I've only seen Spax and Armstrong.
Yes, I have to say that in my heyday it was only Spax available as uprated for the rear & Koni's for the front. Mine have now been sitting for 13years, but hope all will be well when it finally gets on the road: still kack-hander to go first. Small update on that on the thread! |
|
|
|
Topic |
|
Bringing BJU back to life - FINISHED :)
